4 thoughts on “How to make self -made DIY small jewelry”

  1. Vicki

    Make silk net flower bar, make it very beautiful, you can go to Baidu to check the picture
    Method:
    1, the circles, use the No. 3 sleeve total 4
    3, net silk
    4,,, the net Two two slender circles, twist the two circles clockwise at the tail
    5, pull the two circles of circles into the shape of the butterfly front wings
    6, two front wings are tied together
    7, two pieces of
    8 in the back, wrap paper tape
    9, slightly shape to the forefront
    11, use iron wire around the tape to tighten the wire r r
    12, cut off the excess wire
    13, bend the wire slightly, form two beard
    14, the butterfly after the completion, you can put a other needle on the tape, a butterfly hanging jewelry is completed

    and:

    1. Materials and tools
    (L) color metal wire, there are many colors and models.
    (2) Elastic wire mesh, there are various monochrome and two -color.
    (3) Flower core, with various shapes and colors. (4) Self -adhesive tape, there are many colors.
    (5) Synthetic fiber thread for sewing.
    (6) cotton. (7) White glue for woodworking.
    (8) Fast drying adhesive.
    (9) Scissors
    (10) Placing.
    (11) around the circle sleeve, diameter from ICM 8cm. You can also use bottle, pens and other cylindrical items.

    . Basic steps
    This circles, mesh, assembly and shape are the four basic steps for making silk mesh
    .
    (1) Winding
    In the production of petals, flowers, and leaves, the colored metal wire is needed to be circled, which is like their skeleton. For large petals, leaves, and flower supports need to be made one by one. The method of circling is a single circle winding method. For smaller petals, leaves, and flower supports, you can adopt multiple circles. Essence Some special flowers and leaves need to be rushed more, and the petals and leaves with veins need to be added back.
    (1) Single circular winding method
    ① The color metal wire is wrapped on the sleeve for 1 lap, and the first tail of the metal wire is crossed.
    ② At about 5mm on the surface of the leaflet, use your fingers or pointed clamps to clamp the staggered place and tighten it, and then rotate the sleeve 3 to 4 laps vertically.
    ③ Cut the metal wire at the end of the twist or 2cm 5cm wire at the root of the ring.
    (2) Multi -circle winding method
    ① The wire is bent at 5cm.
    ② Hold down the bend with your hand and wrap it on the sleeve with the long one end of the iron.
    ③ Continue around, 316 circles.
    ④ merged four iron wires outside the circle.
    ⑤ Tighten the four metal wires, and then rotate the sleeve 314 longitudinal.
    ⑥ Cut off the unwinded metal wire, or leave two wires with a length of 5cm ·
    (3) Multi -section winding method
    ① Complete the single circle around and change the circle to the required shape Essence
    ② The remaining part of the metal wire continues to circulate, just like the "8" shape.
    ③ can also complete three sections in the same way, and the size of each circle changes according to needs.
    (4) Wave around the circle
    ① Put the color metal wire on the pooled needle first.
    ② Take it off from the needle and stretch it.
    ③ Then go around, the practice is in the same circle.
    (5) Preliminary setting
    The skeleton after the circles is round. According to the basic shape of petals, flowers and leaves in the work, pinch the required shape with your hands. The setting of the multi -circle winding method is as follows.
    ① Pinch with multiple circles together.
    ② Open the circle in a circle
    ③ adjust to the appropriate position.
    (2) mesh wire
    (1) Single circle wire
    ① plainly put on the silk mesh on the metal ring.
    ② Pull the root of the circle.
    ③ After binding several rings at the root of the ring with the thread, the line is pulled directly. ④ After completion, it can be freely shaped.
    (2) Multi -section wire
    ① The same circle mesh silk.
    ② Silk mesh ligation.
    ③ cut off the excess silk.
    ④ Hold two laps on both hands, twisting one circle at the intersection of the two sections, and it can be freely shaped after completion.
    (3) Multi -circle wire
    ① Put on the silk mesh and pull it to the root of the circle. Don't pull too tightly.
    ② tighten the diagonal with the line.
    ③ Wrap the petals out of the piece.
    ④ The roots are tied.
    ⑤ Cut off the excess silk net at the root.

    (3) assembly
    ① Fix the core of the flower core on the stem.
    ② the lower part of the petals is narrower.
    ③ Tie a piece of petals on the stems connected to the flower core without pulling the line.
    ④ continues to tie a piece of petals, repeat all the petals, and then pull the line.
    ⑤ Fix the flower support on the stems.
    ⑥ Turn the flower up.
    的 The appropriate position of the flower stalk is pierced with a leaf.
    ⑧ The appropriate position of the flower stalk is put on the second leaf.
    绿 Banded flowers with green or brown self -stick bands. ⑩ Complete assembly.
    (4) Places, flowers, and leaves can be stretched and bent arbitrarily. According to the type of flower and the blooming of the flowers, the petals, flowers, leaves, and flower stems are organized and shaped. The above -mentioned assembled flowers can obtain different effects as shown in the left.

Leave a Comment